CS062A Micom Temp Controller

CS063C Micom Temp Controller

︳ Specification

Model：CS060
Name：Micom Temp Controller
Operating temperature range：20～34 ℃
Voltage Frequency：See the back of main body
Temperature display：3～34 ℃
Precision：±1℃
Wattage：Max load 1200W
Usage：Aquarium product, control of heating water
Size：
- Body：Width 74 x Height 160 x Deep 40 mm
- Power cord wire：1100mm
- Load extension wire：430mm
- Sensor wire：1000mm
Weight：
- Body：360g

(including power cord wire, sensor wire)

︳ Features

Alarm controlled by Micom chip, yet it won't emit any sound while resetting the temperature or initial lower temperature.
It will emit a sound of alarm and cut the load of heater, if there is ±3℃error happened between actually temperature and setting temperature.
It will emit a sound of alarm and cut the load of heater if the actually temperature is over 35℃ or under 20℃.
When the sensor cable is cut or short-circuited, it will emit a sound of alarm and cut the load of heate.
Failure status is easy to tell by flashing symbols and emitting sounds.
Max Wattage load 1200W.

︳ Instruction Steps

Connecting the the sensor cable and heater to the controller body and power outlet, as above picture shows.
Fully submerse heater and temp. sensor and mount on the tank with suction cups .
Plugging Micom controller into the power outlet.
Using the hook and.double sides tape to fix the controller body in a proper location.

︳Operation

Initial plug in power source, the controller's LED shows the desired temperature of 29℃, later it changes to actual water temperature after twinkling 8 times.
With self detecting system, Micom chip when resetting the temperature or initial lower temperature, it won't emit any sound of alarm if the actual water temperature is lower the desired temperatue 3℃. Only after the controller's red light turning off one time, It will normally emit a sound of alarm.
The desired temperature by pressing the button ▲, press one time to increase 1℃ (up to 34℃).
While setting the temperature, the number on controller's LED will keep twinkling and it is the desired temperature, after it twinkles 8 times the set number then return to the real water temperature.
Controller's red light turns on：The heater is heating.

Alarm of low temperature：If the actual water temperature is below 20℃, the LED shows Lo ,it will emit a sound of alarm and keep heating.

Alarm of high temperature：If the actual water temperature is over 35℃, the LED shows OO . it will emit a sound of alarm and stop heating.

Alarm of ± 3℃：It will emit a sound of alarm, if there is ± 3℃ error happened between actual temperature and setting temperature, when it is over +3℃,the heater will stop heating; while it is below -3℃, the heater will keep heating.
Micom controller can precisely control the heating by back 0.6℃ to protect body's life. (if the temperature change is very tiny and lower than 0.6℃,it won't start heating again and again.)
Correcting the desired temperature： press the button ▼ at same time, after the LED stop twinkling, it shows two units before and after decimal point, to adjust the number by using the screw driver (flat type) to insert the correcting hole on the back of the main body.It will display the correct water temperature after 10 seconds.
The LED returns to normal display：by pressing the button at same time, after the LED stop twinkling, it returns to water temperature of two units place.

︳Important Notes

- Do not stretch into the water by hand without plugging off the power outlet.
- Do not use the damaged power cable or deformed outlet.
- If the power outlet or plug become dirty or oxidized, they must be cleaned to ensure reliable operation.
- Please check if the heater or sensor cable is out of order when any alarm is generated.
- In order to detect the correct water temperature, the heater should be well located to get a better water circulation, and not to close to the temperature sensor.

Page updated

Google Sites

Report abuse