Heater Series
Heater Series
Index > Products > Aquarium > Heater Series > CS064A Series
︳Features
Micro controller makes flash at abnormal temperature.
2 in one LED indicator and thermometer.
Dial easily ,very convenient.
Excellent thermal powder diffusion ,more efficient heat distribution in water.
Fully submersible and excellent water-proof.
Plastic heater guard protects fish against scald.
︳ Technical Specifications
Model:CS064A Series
Name:Micom Led Heater
Size:
OD:32.5mm
Length:100W:340mm
200W:390mm
300W:420mm
︳Reference for choosing Heater
△t°=Optimum aquarium temperature-Minimum room
temperature
Above listed data just for reference
︳Instruction for use
Fully submerse heater and fix it horizontally or vertically to the glass with suction hook and thenplugging in power source.
Light is on:Heating
Light is off:Stop heating
Temperature range:20℃~34℃
Tolerance:±1℃
When the heater uses, please make sure the heater fully submerse in the water. The maximum depth of immersion is 1.2m.
While plugging in power or power failure than back. The LED indicator will show the previous temperature. After flashes 8 times it will turn to the real water temperature.
Press the button one time to increase 1℃ (20℃~34℃ cycle).
When setting temperature. The LED indicator will flashes 8 times then return to the real water temperature.
Heating light on:when the water temperatures doesn't reach the default temperature, the heater will keep heating.
Heating light off:when the water temperatures reached the default temperature, the heater will stop heating.
If the water temperature is over 35℃, LED indicator will flashes and stop heating.
If the water temperature is below 19℃, LED indicator will flashes and keep heating.
Abnormal water temperature:when the LED indicator shows OO is over temperature signal (over 38℃). Besides, shows -- is low temperature signal (below 10℃); both stop heating.
Press the button for over 4 seconds. The LED indicator will show unit and decimal point of the water temperature.
Attention:During the abnormal situation this function is unable to flashes caution.
Press the button for one time the LED indicator returns to normal display.
Abnormal press the button more than 8 seconds. The LED indicator will flashes Er (Error) to caution and stop heating.
︳Important notes
While feeding the noble fish, please add to use the Micom thermostat for dual protection.(The setting Micom thermostat's temperature must be higher than heater temperature by 1℃ or more)
Please avoid hitting the heater and do not use the cracked heater.
When the heater uses, please make sure the heater fully submerse in the water.
Fixed the heater horizontally or vertically to where has better circulation of water.
Plug in the power cord using a drip loop to prevent water from traveling along the cord and coming into contact with the receptacle.
Young children or infirm persons without supervision do not intend the heater for use.
︳Repair & Maintenance
The electric wire can't be replaced, if electric wire has
The plug need to be regularly clean up the contamination
The foreign matters (calcium substance, limescale) on the
※ Method as below:
Prepare 20l water and 200g citric acid.
Put heater in the tank then add citric acid in the water.
Set the temperature for 34℃.
Counting the time for 12 hours then check heater again.
※ Make sure to unplug the power source or cut off the power source before proceeding the repair and maintenance.
︳Emergency Handing
Please cut off the power source and unplug the electric wire for safety, if any situations of danger or urgency happened.
︳Limited Warranty
Under normal use and service, all heaters carry 12 months warranty from the date of purchase on parts and labor against manufacturing defects. Please return the unit if deemed defective to your local dealer for repair or replacement.
The warranty is limited to the heater only, Not responsible for consequential loss or damage.
︳Download